Effect of Iron Chloride Addition on Softwood Lignin Nano-Fiber Stabilization and Carbonization.

This study presents the effect of iron chloride addition on the production of nanocarbon fibers from softwood Organosolv lignin. It was shown that adding 2% FeCl3 to the lignin solution before electrospinning to produce lignin nanofibers increased the thermal resistance of lignin fibers during stabilization. FTIR and XPS analyses of the lignin fibers stabilized with and without FeCl3 revealed that the temperature rate could be increased in the presence of FeCl3 from 1 to 3 °C/min. The optimal temperature to stabilize the lignin fibers was found to be 250 °C, as higher temperatures led to thermal degradation. Also, carbon fibers were successfully produced from pure softwood Organosolv lignin fibers. Carbonization tests were conducted under nitrogen and the best parameters were determined to be a ramp of 10 °C/min until 600 °C with a holding time of 2 h. Furthermore, the effect of 2% FeCl3 addition in the lignin solution was investigated during these processes. XPS analysis showed a 93% carbon content for fibers carbonized with and without FeCl3 addition, while SEM images revealed some surface roughness in fibers with FeCl3 after carbonization. These results confirm that FeCl3 addition influences the carbon nanofiber production.

Optimization of the Electrospray Process to Produce Lignin Nanoparticles for PLA-Based Food Packaging.

The development of new processing methods is required in order to meet the continuous demand for thinner films with excellent barrier properties for food packaging and other applications. In this study, rice husk organosolv lignin nanoparticles were prepared using the electrospray method, which were applied to produce polylactic acid (PLA)-based films for food packaging. The effect of the following electrospray parameters has been investigated: lignin concentration (LC) ranging from 5-50 mg/mL, flow rate (FR) from 0.5-1 mL/min, applied voltage from 10-30 kV, and tip-to-collector distance (TCD) from 10-25 cm, on the morphology, size, polydispersity index (PDI), and Zeta potential (ZP) of lignin nanoparticles (LNPs). The response surface methodology with a Box-Behnken design was applied to optimize these parameters, while dynamic light scattering (DLS) and scanning electron microscopy (SEM) analyses were used to characterize the controlled LNPs. The results showed that the LNPs shape and sizes represent a balance between the solvent evaporation, LC, applied voltage, TCD and FR. The application of optimal electrospray conditions resulted in the production of LNPs with a spherical shape and a minimal size of 260 ± 10 nm, a PDI of 0.257 ± 0.02, and a ZP of -35.2 ± 4.1 mV. The optimal conditions were achieved at LC = 49.1 mg/mL and FR = 0.5 mL/h under an applied voltage of 25.4 kV and TCD = 22 cm. Then, the optimized LNPs were used to improve the properties of PLA-based films. Three types of PLA-lignin blend films were casted, namely lignin/PLA, LNPs/PLA and PLA-grafted LNPs. PLA-grafted LNPs exhibited a more uniform dispersion in PLA for lignin contents of up to 10% than other composite samples. Increasing the lignin content from 5% to 10% in PLA-grafted LNPs resulted in a significant increase in elongation at break (up to four times higher than neat PLA). The presence of PLA-grafted lignin led to a substantial reduction in optical transmittance in the UV range, dropping from 58.7 ± 3.0% to 1.10 ± 0.01%, while maintaining excellent transparency to visible light compared to blends containing lignin or LNPs. Although the antioxidant capacity of unmodified lignin is well-known, a substantial increase in antioxidant capacity was observed in LNPs and PLA-grafted LNP films, with values exceeding 10 times and 12 times that of neat PLA, respectively. These results confirm the significant potential of using studied films in food packaging applications.

Wood color modification with iron salts aqueous solutions: effect on wood grain contrast and surface roughness.

Wood is a biosourced material with unique aesthetic features due to its anatomy and chemical composition. White oak wood surface color can be modified with the use of iron salts, which react with wood phenolic extractives, present as free molecules in wood porous structure. The impact of modifying wood surface color with iron salts on the final appearance of wood, including its color, grain contrast and surface roughness, was evaluated in this study. Results showed that following the application of iron (III) sulphate aqueous solutions on white oak wood surface, its roughness increased, which is due to grain raising after wetting of wood surface. The color modification of wood surface with iron (III) sulphate aqueous solutions was compared with a non-reactive water based blue stain. The contrast associated to wood grain that was expressed by the standard deviation of luminance values in wood images, also increased after application of the iron (III) sulphate aqueous solution on white oak wood surface. The comparison of contrast changes showed that wood samples stained with iron (III) sulphate on their curved surface had the highest increase in grain contrast compared to iron-stained wood showing the straight grain and to wood surfaces colored by a non-reactive water-based stain for both curved and straight grains.

Bioactive Molecules from Myrianthus arboreus, Acer rubrum, and Picea mariana Forest Resources.

Forest trees are the world's most important renewable natural resources in terms of their dominance among other biomasses and the diversity of molecules that they produce. Forest tree extractives include terpenes and polyphenols, widely recognized for their biological activity. These molecules are found in forest by-products, such as bark, buds, leaves, and knots, commonly ignored in forestry decisions. The present literature review focuses on in vitro experimental bioactivity from the phytochemicals of Myrianthus arboreus, Acer rubrum, and Picea mariana forest resources and by-products with potential for further nutraceutical, cosmeceutical, and pharmaceutical development. Although these forest extracts function as antioxidants in vitro and may act on signaling pathways involved in diabetes, psoriasis, inflammation, and skin aging, much still remains to be investigated before using them as therapeutic candidates, cosmetics, or functional foods. Traditional forest management systems focused on wood must evolve towards a holistic approach, allowing the use of these extractives for developing new value-added products.

Recycled HDPE/Natural Fiber Composites Modified with Waste Tire Rubber: A Comparison between Injection and Compression Molding.

With the objective of turning wastes into added-value materials, sustainable and fully recycled wood-plastic composites were reinforced by waste tire rubber particles to show balanced properties and potentially low-cost materials. Recycled high density polyethylene (rHDPE) was compounded (melt extrusion) with flax fiber (FF) and waste regenerated tire rubber (RR) to investigate the effect of mixing ratio, coupling agent (maleated polyethylene, MAPE) and molding process (injection and compression molding) on the properties of hybrid composites. In particular, a complete set of characterization was performed including thermal stability, phase morphology and mechanical properties in terms of tension, flexion and impact, as well as hardness and density. Adding 40 wt.% of flax fibers (FF) increased the tensile (17%) and flexural (15%) modulus of rHDPE, while the impact strength decreased by 58%. Substitution of FF by waste rubber particles improved by 75% the impact strength due to the elasticity and energy absorption of the rubber phase. The effects of impact modification were more pronounced for rHDPE/(FF/RR) compatibilized with MAPE (10 wt.%) due to highly improved interfacial adhesion and compatibility. The results also suggest that, for a fixed hybrid composition (FF/RR, 25/55 wt.%), the injection molded composites have a more homogenous morphology with a uniform distribution of well embedded reinforcements in the matrix. This better morphology produced higher tensile strain at break (12%) and impact strength (9%) compared to compression molded samples.

Monitoring transformation of two tropical lignocellulosics and their lignins after residence in Benin soils.

Thermally assisted Hydrolysis and Methylation (THM), and 2D-heteronuclear single quantum coherence nuclear magnetic resonance (2D HSQC NMR) spectroscopy were used to monitor the transformation of ramial chipped wood (RCW) from Gmelina arborea and Sarcocephalus latifolius, together with their organosolv lignins, following soil incubation in Benin (West Africa). Mesh litterbags containing RCW were buried in soils (10 cm depth) and were retrieved after 0, 6, 12 and 18 months of field incubation. Chemical analysis showed that total carbohydrate content decreased, while total lignin content increased as RCW decomposition progressed. Ash and mineral content of RCW increased significantly after 18 months of decomposition in soil. Significant N-enrichment of the RCW was determined following 18 months incubation in soils, reaching 2.6 and 1.9 times the initial N-content for G. arborea and S. latifolius. Results of THM showed that the S + G sum, corresponding to lignins, increased with RCW residence time in the soils, in contrast to the response of compounds derived from carbohydrates, the sum of which decreased. Remarkably, lignin interunit linkages, most notably ß-O-4' aryl ethers, ß-ß' resinol, ß-5' phenylcoumaran and p-PCA p-coumarate, survived after 18 months in the soil, despite their gradual decrease over the duration of the experiment.

Acidic Ionic Liquid as Both Solvent and Catalyst for Fast Chemical Esterification of Industrial Lignins: Performances and Regioselectivity.

Lignin can be considered an essential under-exploited polymer from lignocellulosic biomass representing a key for a profitable biorefinery. One method of lignin valorization could be the improvement of physico-chemical properties by esterification to enhance miscibility in apolar polyolefin matrices, thereby helping the production of bio-based composites. The present work describes for the first time a succeeded chemical esterification of industrial lignins with maleic anhydride in an acidic ionic liquid: 1-butyl-3-methyl imidazolium hydrogen sulfate without additional catalyst. This efficient strategy was applied to four industrial lignins: two softwood Kraft lignins (Indulin AT, Wayagamack), one hardwood Kraft lignin (Windsor), and one softwood organosolv lignin (Lignol), distinct in origin, extraction process and thus chemical structure. The chemical, structural, and thermal properties of modified lignins were characterized by 31P nuclear magnetic resonance, infrared spectroscopy and thermal analyses, then compared to those of unmodified lignins. After 4 h of reaction, between 30 to 52% of the constitutive hydroxyls were esterified depending on the type of lignin sample. The regioselectivity of the reaction was demonstrated to be preferentially orientated toward aliphatic hydroxyls for three out of four lignins (66.6, 65.5, and 83.6% for Indulin AT, Windsor and Lignol, respectively, vs. 51.7% for Wayagamack). The origin and the extraction process of the polymer would thus influence the efficiency and the regioselectivity of this reaction. Finally, we demonstrated that the covalent grafting of maleyl chain on lignins did not significantly affect thermal stability and increased significantly the solubility in polar and protic solvent probably due to additional exposed carboxylic groups resulted from mono-acylation independently of H/G/S ratio. Blending with polyolefins could then be considered in regard of compatibility with the obtained physico-chemical properties.

Further isolation and identification of anti-diabetic principles from root bark of Myrianthus arboreus P. Beauv.: The ethyl acetate fraction contains bioactive phenolic compounds that improve liver cell glucose homeostasis.

ETHNOPHARMACOLOGICAL RELEVANCE: We recently reported that ethanol extract of Myrianthus arboreus P. Beauv. root bark demonstrated antidiabetic activity by modulating hepatocyte glucose homeostasis. This activity was associated significantly to the ethyl acetate (EAc) fraction. The current study sought to identify the active compounds responsible of the antidiabetic effect of M. arboreus in the EAc fraction using bioassay-directed sub-fractionation. MATERIALS AND METHODS: EAc fraction was sub-fractionated using Flash chromatography. Preparative HPLC was used to isolate the pure compounds. The structures of the isolated compounds were confirmed by analysis of NMR spectroscopic and mass spectrometric data. Hepatic (H4IIE, HepG2) cells were treated with maximum non-toxic concentrations of ethanol extract, its EAc fraction and isolated compounds thereof. Glucose-6-phosphatase (G6Pase) activity was measured using the glucose oxidase method. To measure glycogen synthase (GS) activity, radioactive assays were used. Phosphorylation of AMP-activated protein kinase (AMPK) and Glycogen Synthase Kinase-3 (GSK-3) were probed by Western blot. RESULTS: Six sub-fractions were obtained, and the antidiabetic activity was found in two sub-fractions (SFE1 and SFE2). For the first time, two known C-glycosylflavone regio-isomers, isoorientin (1) and orientin (2) were detected and isolated from M. arboreus plant, especially from SFE2 as well as protocatechuic acid, 3,4-dihydroxybenzaldehyde (4), and chlorogenic acid isolated from SFE1. The compounds 1, 2, 4 were determined to decrease the activity of G6Pase by increasing AMPK phosphorylation and to stimulate GS through GSK-3 phosphorylation. Isoorientin which is one of the main compounds of EAc fraction, expressed the strongest effect in all bioassays, similar to that of the EAc fraction. A significant and linear correlation was found between the phosphorylation of AMPK and the activity of G6Pase modulated by all samples (R2 = 0.54; p < 0.05). Similar to G6Pase assay, a correlation was determined between the capacity of M. arboreus extracts/fractions/compounds to stimulate GS activity and to phosphorylate GSK-3 (R2 = 0.57, p < 0.01). CONCLUSION: Results demonstrate that 1, 2, 4 are responsible, at least in part, for the antidiabetic activity of M. arboreus. These compounds can be used to ensure the quality and efficacy of M. arboreus antidiabetic preparations and standardize such preparations.

Metabolite Profiling of Two Maple-Derived Products Using Dereplication Based on High-Performance Liquid Chromatography-Diode Array Detector-Electrospray Ionization-Time-of-Flight-Mass Spectrometry: Sugar Maple Bark and Bud Hot-Water Extracts.

Recent studies about hot-water extracts from sugar maple (Acer saccharum Marsh.) bark and buds demonstrated that they contain high amounts of phenolic structures that may be used as antioxidant food additives. However, the detailed chemical composition of these maple-derived extracts has yet to be determined. By performing high-performance liquid chromatography-diode array detector-high-resolution mass spectrometry (HPLC-DAD-HRMS)-based dereplication, we were able to spike and classify almost 100 metabolites in each hot-water extract. The sugar maple bark hot-water extract is rich in simple phenolic compounds and phenylpropanoid derivatives, while bud extract contains predominantly flavonoids, benzoic acids, and their complex derivatives (condensed and hydrolyzable tannins). Among those chemical structures, we tentatively identified 69 phenolic compounds potentially reported for the first time in the genus Acer. Considering the growing commercial demand in natural products, the phenolic fingerprints of sugar maple bark and bud hot-water extracts will help in promoting these two maple-derived products as new sources of bioactive compounds in the food, nutraceutical, and cosmetic industries.

Surface Chemical Changes of Sugar Maple Wood Induced by Thermo-Hygromechanical (THM) Treatment.

The aim of this study was to investigate the effects of heat and steam on the chemical properties of thermo-hygromechanical (THM)-densified sugar maple wood. The THM densification process was performed at two different temperatures (180 °C and 200 °C) with and without steam. The functional groups, surface chemical composition and internal structure and components of the control and densified samples were investigated using attenuated total reflection Fourier transform infrared (ATR-FTIR), X-ray photoelectron (XPS) spectroscopy and pyrolysis gas chromatography-mass spectrometry (Py-GC/MS). The obtained results suggest that the THM densification treatment resulted in significant chemical changes on the wood surface. The results of the ATR-FTIR spectra confirmed the decomposition of hemicelluloses and the relative increase of cellulose and lignin contents on the wood surface. The Py-GC/MS and XPS results show an increase of the oxygen/carbon atomic (O/C) ratio, which indicated that chemical substances containing oxygenated functionality were formed through the densification process. The densification treatment favored the depolymerization of hemicelluloses and cellulose as indicated by an increased anhydrous sugar (levoglucosan) release during the pyrolysis process. Densification also facilitated the cleavage of the lignin side chains, resulting in increased phenyl units with short chains released during the pyrolysis process.

Anhydroglucitol-core gallotannins from red maple buds modulate viability of human blood neutrophils.

Apoptosis of neutrophils is an essential checkpoint for the resolution of inflammation by shutting down the deleterious functions of these immune cells. This study investigated the role of anhydroglucitol-core gallotannins (ACGs) in apoptosis increase of human blood neutrophils treated by the hot water extract from red maple buds (RMB). Fractions obtained by liquid-liquid partitioning (ethyl acetate, butanol and water-remaining fractions) of the hot water extract from RMB were assessed for their effects on neutrophil viability by using flow cytometry. These fractions were then phytochemically analyzed to investigate the ability of major compounds to induce neutrophil apoptosis individually. Ethyl acetate and butanol fractions that contained the major ACGs ginnalin A, ginnalin 3,6 and ginnalin C stimulated the apoptosis of neutrophils. The three ACGs at 100 µM significantly increased the rate of the late apoptotic cells. When differentially combined, these ACGs have additive or antagonist effects. These effects are related to the concentrations of the constituents in the mixtures studied, especially so for ginnalin C. GinA increased FADD, phospho-Rad17, SMAC/Diablo and cytochrome C, while decreasing the anti-apoptotic protein catalase. These compounds could be useful for the development of novel therapeutic approaches that facilitate resolution of neutrophil-mediated inflammatory diseases.

Bioactive Pentacyclic Triterpenes from the Root Bark Extract of Myrianthus arboreus, a Species Used Traditionally to Treat Type-2 Diabetes.

Four new Δ12 ursene-type pentacyclic triterpenes containing the trans-feruloyl moiety (1-4), along with ursolic acid (5), were isolated from a Myrianthus arboreus root bark ethanol extract, after bioassay-guided subfractionation of its hexane fraction. The structures of 1-4 were established on the basis of the results of standard spectroscopic analytical methods (IR, HRESIMS, GC-MS, 1D and 2D NMR). The compounds 3ß- O- trans-feruloyl-2α,19α-dihydroxyurs-12-en-28-oic acid (1), 2α-acetoxy-3ß- O- trans-feruloyl-19α-hydroxyurs-12-en-28-oic acid (3), and 5 were determined to decrease the activity of hepatocellular glucose-6-phosphatase (G6Pase) and to activate glycogen synthase (GS). Their action on G6Pase activity implicated both Akt and AMPK activation. In addition, these compounds were determined to stimulate GS via the phosphorylation of glycogen synthase kinase-3. Compound 3 showed the most potent effect in modulating glucose homeostasis in liver cells. This is the first comprehensive report on novel phytochemical components of the root bark extract of M. arboreus based on the isolation of the principles responsible for its antidiabetic effects.

Nutrients, Antioxidant Capacity and Safety of Hot Water Extract from Sugar Maple (Acer saccharum M.) and Red Maple (Acer rubrum L.) Bark.

Sugar maple (Acer saccharum M.) and red maple (Acer rubrum L.) barks were treated with hot water to extract nutrients in order to explore, for the first time, its potential as safe dietary antioxidants. The organic and inorganic nutrients of these extracts, as well as their safety on human PLB-985 cells differentiated into neutrophils-like cells, were determined. Proximate analysis showed that both bark extracts were low in moisture and fat. Sugar maple bark extract (SM-BX) showed crude protein and ash content higher than those found in red maple bark extract (RM-BX). In addition, SM-BX had total sugars higher than those evaluated in RM-BX, while complex sugars (oligo- and/or poly-saccharides) were similarly abundant in both bark extracts. Furthermore, SM-BX demonstrated a wide array of vital minerals (K, Ca, Mg, P, Na, Fe and Cu) in quantity larger than that evaluated in RM-BX, whereas RM-BX have Zn and Mn levels higher than those found in SM-BX. Phytochemical analyses showed that RM-BX exhibited total phenolic and flavonoid contents higher than those measured in SM-BX. Consequently, RM-BX presented an antioxidant activity higher than that of SM-BX: 2.85-fold ABTS radical cation scavenging capacity and 1.9-fold oxygen radical absorbance capacity. Finally, RM-BX and SM-BX were greatly safe since, at concentration up to 100 µg/ml, they did not modify the viability of neutrophils as determined by flow-cytometry assay using Annexin V-FITC/Propidum Iodide as markers. In conclusion, our in vitro studies indicate that both red and sugar maple bark extracts have a real potential as food additives.

Root bark extracts of Myrianthus arboreus P. Beauv. (Cecropiaceae) exhibit anti-diabetic potential by modulating hepatocyte glucose homeostasis.

ETHNOPHARMACOLOGICAL RELEVANCE: Myrianthus arboreus P. Beauv. is a tropical tree used in African folk medicine, including for diabetes. However, little research has yet been conducted to support this ethnopharmacological use of this plant. The present study sought to determine the antidiabetic potential of root bark extracts through cell-based bioassays of liver and muscle glucose homeostasis. MATERIALS AND METHODS: Four extracts were obtained from crude root bark powder: 1 aqueous (AQ), 2 ethanol (EtOH), 3 alkaloid enriched (Alk) (obtained from methanol extract) and 4 dichloromethane (Dic) extracts. Moreover, extract 2 was further separated into two fractions: 2.1 ethyl acetate (EAc) and 2.2 hexane (Hex). To assess the antidiabetic activity of the plant extracts, inhibition of glucose-6-phosphatase (G6Pase), stimulation of glycogen synthase (GS) and modulation of glucose uptake were determined in cultured H4IIE and HepG2 hepatocytes as well as C2C12 myocytes, respectively. Phosphorylation of three kinases, AMP-activated protein kinase (AMPK), Akt and Glycogen Synthase Kinase-3 (GSK-3) were probed by Western blot. RESULTS: M. arboreus extracts/fractions did not stimulate glucose uptake in C2C12 cells albeit 2.2 (Hex) fraction showed a mild positive tendency. In contrast, extract 2 and its fractions as well as extract 3 were able to decrease hepatocyte G6Pase activity. Their effect on G6Pase activity involved both Akt and AMPK phosphorylation. No significant correlation was observed between activation of Akt and inhibition of G6Pase (R2 = 0.50 p < 0.14), whereas that between stimulation of AMPK and inhibition of G6Pase was statistically significant (R2 = 0.75 p < 0.05). On the other hand, extract 2, its fraction 2.2 and extract 3 were able to stimulate GS through GSK-3 phosphorylation. A high correlation was observed between the ability of M. arboreus extracts and fractions to phosphorylate GSK-3 and modulate GS activity (R2=0.81 p < 0.01). Extract 2 and its fraction 2.2 together with extract 3 were the only plant products to simultaneously and potently regulate G6Pase and GS, the key players of hepatic glucose homeostasis. CONCLUSION: Overall, these data support the traditional antidiabetic uses of the root bark of M. arboreus.

Optimization of Bioactive Polyphenols Extraction from Picea Mariana Bark.

Reported for its antioxidant, anti-inflammatory and non-toxicity properties, the hot water extract of Picea mariana bark was demonstrated to contain highly valuable bioactive polyphenols. In order to improve the recovery of these molecules, an optimization of the extraction was performed using water. Several extraction parameters were tested and extracts obtained analyzed both in terms of relative amounts of different phytochemical families and of individual molecules concentrations. As a result, low temperature (80 °C) and low ratio of bark/water (50 mg/mL) were determined to be the best parameters for an efficient polyphenol extraction and that especially for low molecular mass polyphenols. These were identified as stilbene monomers and derivatives, mainly stilbene glucoside isorhapontin (up to 12.0% of the dry extract), astringin (up to 4.6%), resveratrol (up to 0.3%), isorhapontigenin (up to 3.7%) and resveratrol glucoside piceid (up to 3.1%) which is here reported for the first time for Picea mariana. New stilbene derivatives, piceasides O and P were also characterized herein as new isorhapontin dimers. This study provides novel information about the optimal extraction of polyphenols from black spruce bark, especially for highly bioactive stilbenes including the trans-resveratrol.

Suitability of DPPH spiking for antioxidant screening in natural products: the example of galloyl derivatives from red maple bark extract.

To investigate the antioxidant potential in natural products, radical scavenging tests (ABTS, DPPH, ORAC, etc.) are usually considered as the first approach. In addition to the standard colorimetric assays, methods using separation techniques (on-line and pre-column assays) have been developed in the past decades. Based on the peak area (PA) reductions of compounds monitored by HPLC, the pre-column spiking method allows rapid characterisation of natural matrices avoiding laborious isolation steps. However, available information about the significance of the results produced remains scarce. Here, we report, for the first time, a discussion of the potential of the pre-column DPPH spiking method to pinpoint antioxidant compounds using red maple bark extract (RMBE). First, DPPH spiking was conventionally applied to the galloyl compounds in the extract showing the inadequacy of assessing results by PA reductions. The method was then applied to pure galloyl derivatives, evaluating their molar amount reacted (MAR) for more significance. The comparison with the standard DPPH-HPLC/AE method directly monitoring DPPH• inhibition highlighted the inability to retrieve the respective antioxidant efficiencies (AE) of each compound by using DPPH spiking. Despite its limitations, the DPPH spiking method brought to light an autoxidation phenomenon and a matrix/mixture effect investigated through tertiary mixtures of galloyl compounds. Although restricted to the compounds from one natural matrix, this study questions the validity of the spiking method as usually performed and could serve as a basis for further investigations (explorations of other natural products, kinetics considerations). Graphical abstract Investigation of the pre-column DPPH spiking method through the case of galloyl derivatives.

Antioxidant Capacity, Phenolic Constituents and Toxicity of Hot Water Extract from Red Maple Buds.

The present study reports, for the first time, the results of the antioxidant capacity and the phenolic composition of a hot water extract from red maple buds (RMB), as well as its safety. In this regard and comparatively to antioxidant standards, this extract exhibits a significant antiradical capacity when tested by 2,2-diphenyl-1-picrylhydrazyl (DPPH· ) and anion superoxide trapping assays. High-resolution mass spectrometric and nuclear magnetic resonance analyses permitted to determine for the first time, in red maple species, cyanidin-3-O-glucoside, quercetin-3-O-galactoside, quercetin-3-O-arabinoside, and quercetin. Also, the quantification of individual phenolics by high-performance liquid chromatography method revealed that ginnalin A at 117.0 mg/g is the major compound of RMB hot water extract. Finally, using flow cytometry evaluation, the extract of RMB was determined to have no toxicity neither to cause significant modification of apoptosis process, up to concentration of 100 µg/ml, on human peripheral blood neutrophils. These results allow anticipating various fields of application of RMB water extract.

Study of Organosolv Lignins as Adhesives in Wood Panel Production.

Organosolv lignins obtained from sugar maple bark and wood were studied as adhesives for wood particleboard production. Organosolv pulping of sugar maple wood and bark was carried out in the presence of Lewis acid FeCl3 as a catalyst. The organosolv lignins recovered from this process were investigated by determination of Klason plus acid-soluble lignin content, of sugars by HPLC analysis, and of ash content. Structural characterizations of these lignins were performed by Fourier-transform infrared (FT-IR) and by 31P NMR. The results of the latter studies indicate that the content of free phenolic groups was more important in bark than in wood lignin. The gel permeation chromatography (GPC) analyses results suggested that the weight-average molecular mass of wood lignin was higher than that of bark lignin. The studied organosolv lignins were used for the preparation of particleboards as recovered and in combination with glyoxal or isocyanate. It was found that sugar maple bark lignin, as such or modified with isocyanate, was a more efficient adhesive than its wood counterpart. On the contrary, it was the organosolv wood lignin combined with glyoxal which was a more efficient adhesive than its bark counterpart. In combination with isocyanate, it was the sugar maple bark organosolv lignin which was determined to have the best adhesive performance of all studied lignins.

Enzymatic Transesterification of Kraft Lignin with Long Acyl Chains in Ionic Liquids.

Valorization of lignin is essential for the economic viability of the biorefinery concept. For example, the enhancement of lignin hydrophobicity by chemical esterification is known to improve its miscibility in apolar polyolefin matrices, thereby helping the production of bio-based composites. To this end and due to its many reactive hydroxyl groups, lignin is a challenging macromolecular substrate for biocatalyzed esterification in non-conventional media. The present work describes for the first time the lipase-catalyzed transesterification of Kraft lignin in ionic liquids (ILs). Three lipases, three 1-butyl-3-methylimidazolium based ILs and ethyl oleate as long chain acyl donor were selected. Best results were obtained with a hydrophilic/hydrophobic binary IL system (1-butyl-3-methylimidazolium trifluoromethanesulfonate/1-butyl-3-methylimidazolium hexafluoro- phosphate, 1/1 v/v) and the immobilized lipase B from Candida antarctica (CALB) that afforded a promising transesterification yield (ca. 30%). Similar performances were achieved by using 1-butyl-3-methylimidazolium hexafluorophosphate as a coating agent for CALB rather than as a co-solvent in 1-butyl-3-methylimidazolium trifluoromethane-sulfonate thus limiting the use of hydrophobic IL. Structural characterization of lignin oleate was performed by spectroscopic studies (FTIR and ¹H-NMR). The synthesized lignin oleate exhibited interesting thermal and textural properties, different from those of the original Kraft lignin.

Study of Polyphenol Content and Antioxidant Capacity of Myrianthus Arboreus (Cecropiaceae) Root Bark Extracts.

In order to evaluate the therapeutic potential of polyphenolic extracts from root bark of M. arboreus, we have determined the content of various polyphenols in aqueous and ethanol (EtOH) extract as well as two sub-fractions of the latter: ethyl acetate (EAc) and hexane (Hex). The total phenols, flavonoids, hydroxycinnamic acids and proanthocyanidins have been determined for all studied extracts/fractions by spectrophotometric methods. Both TP content (331.5 ± 2.5 mg GAE/g) and HCA content (201 ± 1.5 mg CAE/g) were determined to be the highest in EAc fraction of EtOH extract. All studied extracts were however determined to have a low content in flavonoids. The determination of antioxidant capacities of the studied extracts has also been performed by the following in vitro antioxidant tests: DPPH scavenging, phosphomolybdenum method and oxygen radical absorbance (ORACFl and ORACPRG) assay. The results of the DPPH free radical and ORACFl assays showed that there is no significant difference between the EAc fraction and Oligopin(®), but the EAc fraction exhibited the highest antioxidant capacity as determined by the phosphomolybdenium method. In addition, the EtOH extract was determined to have the same antioxidant efficiency as the synthetic antioxidant BHT or commercial extract Oligopin(®) by phosphomolybdenum method. On the other hand, a positive correlation (r < 0.6) was found between different classes of polyphenols and the results of the phosphomolybdenum method, ORACFl as well as ORACPRG, except for the DPPH assay, for which a negative correlation was indicated (r < 0.62). Interestingly, it seems that the content in hydroxycinnamic acids played a big role in all assays with r < 0.9. According to the present study, EAc fraction and EtOH extract should be further studied for the potential use in the pharmaceutical and food industry.